can_physical_layer:can_transceivers

Welcome to the CAN-bus Wiki project
This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== CAN Transceivers =======

The CAN transceiver has two tasks:
  * Receiving: it adapts signal levels from the bus, to levels that the CAN Controller expects and has protective circuitry that protect the CAN Controller
  * Sending: it converts the transmit-bit signal received from the CAN Controller into a signal that is sent onto the bus


The following is a list of known manufacturers of CAN transceivers.\\ Not all of there products are listed but sometimes products worth mentioning. Always check the manufacturers product pages.

Manufacturers working on CAN FD capable transceivers are marked with a CAN FD smily :-)
The main issue of CAN FD capable transceivers is the symmetry of the rising and the falling edges, which are required above 1 Mbit/s. CAN FD enhances the exchange of data up to 5 Mbit/s by using high-speed (HS) CAN transceivers. But its achievable data rate is not likely to exceed 2 Mbit/s in real topologies because of the effects of signal ringing. CAN SIC transceivers actively improve the signal and thus are less limited by ringing, achieving higher bit rates in more complex topologies.




----
===== Application Notes and White Papers =====

  * [[http://www.onsemi.com/pub_link/Collateral/AND8352-D.PDF | AND8352]] NCV7341 CAN Transceiver, Behavior with a Permanent Short on the CAN Bus; [[http://www.onsemi.com/ | On Semiconductor]]
  * [[http://www.onsemi.com/pub_link/Collateral/AND8365-D.PDF | AND8365/D]]. 125 kbps with AMIS-4168x; [[http://www.onsemi.com/ | On Semiconductor]]

===== Analog Devices =====
  * [[https://www.analog.com/en/products/adm3055e.html |ADM3055E]] new member of the [[http://www.analog.com/en/content/CU_over_iCoupler_Digital_Isolation/fca.html|iCoupler]] family of galvanic-isolated CAN transceivers, complies with ISO 111898-2:2016, bit rates up to 12 Mbit/s, low loop delays of 150 ns, ±40 V bus fault protection on CAN bus pins CAN-FD, :-)

  * [[http://www.analog.com/en/interface/can/adm3054/products/product.html|ADM3054]] Transceiver with galvanic isolation, 3 channel [[http://www.analog.com/en/content/CU_over_iCoupler_Digital_Isolation/fca.html|iCoupler]]. Logic Voltage supply is 3.3V  or 5V, bus voltage supply 5V. Isolation 5KV<sub>RMS</sub>. Max bit rate 1Mbit/s , temp range -40°C to +125°C. 16pin SOIC-W.\\ [[http://www.analog.com/static/imported-files/data_sheets/ADM3054.pdf| Data Sheet(pdf)]]

  * [[http://www.analog.com/en/search.html?q=ADM3053 | ADM3053]] Signal and Power Isolated CAN Transceiver with Integrated Isolated DC-to-DC Converter

----

===== Atmel =====
  * [[ http://www.atmel.com/devices/ATA6560.aspx | ATA6560]] and [[ http://www.atmel.com/devices/ATA6561.aspx | ATA6561]] Compliant with ISO11898-2, ISO11898-5 and SAEJ2284, Supporting CAN FD :-) up to 5Mbit/s. supply voltage 5 V, IO voltage 3-5 V, SO8 and DFN8 package. The March 2015 CAN Newsletter (CiA) has an [[http://v2.can-newsletter.org/uploads/media/raw/b47a469f1106f276e0bcaa31fc957424.pdf | article]] on page 16-17. 

----
===== Cobham =====
[[http://www.cobham.com/| Cobham]] (formerly Aeroflex)

[[http://ams.aeroflex.com/pagesproduct/datasheets/UT64CAN333x.pdf  | UT64CAN333x]] series :-). rates from 10 kbit/s to 8 Mbit/s, radiation performance of 100 krad. Suited for flight applications.
  * UT64CAN3330 sleep-mode operation ISO 11898-5.
  * UT64CAN3331 Diagnostic Loopback
  * UT64CAN3332 Auto-Baud Loopback


===== DMOS / ELMOS =====
:-)

[[http://www.dmosdesign.com/index.php?option=com_content&view=article&id=48%3Acan&catid=21%3Awire-com&Itemid=52&lang=en | DMOS]] and [[http://www.elmos.com/produkte/interface/can-transceiver-and-system-basis-chip.html | ELMOS]] do have CAN transceivers for 11898-2/-5/-6. The companies are working on **CAN FD** transceivers.


----
===== Freescale =====
:-)

[[http://www.freescale.com/MC33901 | MC33901]] and [[http://www.freescale.com/MC34901 | MC34901]] High-Speed CAN Transceivers for Industrial and Automotive Applications with high EMC performance and high ESD robustness and low power consumption of 8µA in stand by mode. Other features are
  * ±6kV ESD, >36Bm DPI
  * 5V and 3.3V I/O compatibility with auto-detect
  * Excellent EMC performance supports **CAN FD** up to 2 Mbps
Both are different in: 
  * [[http://www.freescale.com/MC33901 | MC33901]] Automotive specific built-in “Tx Dominant Timeout” feature
  * [[http://www.freescale.com/MC34901 | MC34901]] Industrial built-in support for long-length and low baud rate networks

----
===== Holt Integrated Circuits =====
  * [[http://www.holtic.com/ | HI-3000H ]] 1-Mbit/s CAN transceiver for avionics applications. It is specified to operate from -55 °C to +175 °C for plastic packages and -55 °C to +200 °C for the ceramic Cerdip-8 package. The component is compatible with the Arinc 825 specification and the ISO 11898-5 standard. Up to 120 nodes may be used in one CAN network.


----
===== Infineon =====
:-)

[[http://www.infineon.com/cms/en/product/transceiver/industrial-transceiver/channel.html?channel=db3a304320d39d590121f360c6630d59 | Industrial transceivers overview]]
[[http://www.infineon.com/cms/en/product/transceiver/automotive-transceiver/automotive-can-transceivers/channel.html?channel=ff80808112ab681d0112ab69d0840321 | Automotive Transceivers overview]]

Infineon [[https://www.infineon.com/cms/en/tools/solution-finder/product-finder/transceiver-finder/| Transceiver Finder]]

For CAN High Speed applications (ISO11898-2, ISO11898-6), Infineon offers three transceivers 
  * IFX1050G (for 5,0V I/O-Logiksysteme)
  * [[http://www.infineon.com/cms/en/product/transceiver/industrial-transceiver/IFX1050G+VIO/productType.html?productType=db3a30442c64a1a6012c73a785600950 | IFX1050GVIO]] (for 3,3V I/O-Logiksysteme)
  * IFX1051LE ???
  * IFX1040SJ (with Wakeup-functionality).
  * TLE6250 up to 1 Mbit/s
  * TLE9250 series will support bit-rates up to 5 Mbit/s :-)   (CiA info)

Fault Tolerant Low Speed CAN-Transceiver (ISO11898-3)
  * IFX1054G is suited for applications requiring fault tolerance robustness at lower data rate

==== System Basis Chip ====
  * [[https://www.infineon.com/cms/de/product/automotive-system-ic/system-basis-chips-sbc/mid-range-sbc-family/tle9263-3bqx/ | TLE9263-3BQX]] designed for various CAN-LIN automotive applications as main supply for the microcontroller and as interface for a LIN and CAN bus network including the CAN Partial Networking feature, HS-CAN transceiver supporting CAN-FD up to 5 Mbps and CAN Partial Networking (incl. FD tolerant mode) ISO 11898-2:2016
  * TLE826x  with high speed CAN transceiver
  * TLE9267  with selective wake-up CAN transceiver. IC developed for door control units.
  * TLE9278 chip features four CAN transceivers qualified for 5 Mbit/s. :-)   (CiA info)

----
===== Linear Technology =====

  * [[http://www.linear.com/product/LTC2875 | LTC2875]] high speed, low power CAN transceiver operating on 3.3V or 5V
    * Protected from Overvoltage Line Faults to ±60V
    * High Speed Operation Up to 4Mbps
    * ±25kV ESD Interface Pins, ±8kV All Other Pins
    * Variable Slew Rate Driver with Active Symmetry Control and SPLIT Pin for Low Electromagnetic Emission (EME)
    * Extended Common Mode Range (±36V)
    * Current Limited Drivers and Thermal Shutdown
    * Transmit Data (TXD) Dominant Timeout Function
    * Up to –55°C to 125°C available
    * 3mm × 3mm 8-Lead DFN and SO-8 Packages


----

===== Maxim =====
The MAX14878–MAX14880 family of high-speed transceivers improve communication and safety by integrating galvanic isolation between the CAN protocol controller side of the device and the physical wires of the CAN bus network. All transceivers operate up to the maximum high-speed CAN data rate of 1Mbps. Input common-mode range is ±25V, wide 1.71V to 5.5V supply voltage range, 40°C to +125°C,
  * [[https://www.maximintegrated.com/en/products/interface/transceivers/MAX148788.html | MAX14878]]  up to 5000VRMS (60s) of galvanic isolation.
  * [[https://www.maximintegrated.com/en/products/interface/transceivers/MAX148789.html | MAX14879]] provides up to 2750VRMS (60s) of galvanic isolation,
  * [[https://www.maximintegrated.com/en/products/interface/transceivers/MAX14880.html  | MAX14880]] up to 5000VRMS (60s) of galvanic isolation. 


===== Microchip =====
  * [[https://www.microchip.com/wwwproducts/en/ATA6570 | ATA6570]] High-speed CAN FD Transceiver with Partial Networking, provides local and enhanced remote wake-up capabilities. Very low power consumption in Standby and Sleep Mode. Beside local wake-up via WAKE and remote wake-up pattern according to ISO 11898-2:2016 and also additionally supports ISO11898-2:2016 compliant CAN partial networking. Configuration the SPI. It also features a watchdog, a Serial Peripheral Interface (SPI) and automatic adjustment of the I/O levels to the I/O level of the connected microcontroller via the VIO pin. ATA6570 is a CAN-FD device but can be easily configured via the SPI as Non-FD for Classical CAN, CAN FD silent, CAN FD passive or as CAN FD active device, in order to fulfill the corresponding application requirements. :-)
  * [[ http://www.microchip.com/wwwproducts/en/MCP2542FD | MCP2542FD/4FD]] CAN FD Transceiver with Wake-Up on CAN activity,  Optimized for CAN FD at 2, 5 and 8 Mbps Operation, Maximum propagation delay 120 ns, Loop delay symmetry -10%/+10% (2 Mbps), ([[http://ww1.microchip.com/downloads/en/DeviceDoc/20005514A.pdf| PDF]]) :-)
  * [[ http://www.microchip.com/wwwproducts/en/MCP2542FD | MCP2542WFD/4WFD]] CAN FD Transceiver with Wake-Up Pattern (WUP) Option, Optimized for CAN FD at 2, 5 and 8 Mbps Operation, Maximum propagation delay 120 ns, Loop delay symmetry -10%/+10% (2 Mbps), Wake-up on Pattern (WUP) as specified in ISO11898-2:2015, 3.6 μs activity filter time. [[http://ww1.microchip.com/downloads/en/DeviceDoc/20005514A.pdf| PDF]]) :-)
  * [[ http://www.microchip.com/wwwproducts/Devices.aspx?dDocName=en561070 | MCP2561/2]] High-Speed CAN transceivers ISO-11898-5, low standby current consumption (<5 µA typical). VDD= 4.5V to 5.5V. Both meet CAN specification requirement “GIFT ICT Group Conformance Test Specification V1.0”\\ :-) Microchip claims that its MCP2561/2FD transceivers are suitable for data-rates up to 8 Mbit/s. The maximum propagation delay is 120 ns and the loop-delay symmetry is ±10 % for bit-rates up to 2 Mbit/s.
    *  MCP2561 SPLIT pin to stabilize common mode in biased split termination schemes.
    *  MCP2562 VIO Supply Pin to Interface directly to 1.8V to 5.5V I/O, internal level shifter on digital I/O pins.
  * [[http://www.microchip.com/wwwproducts/Devices.aspx?dDocName=en010405 | MCP2551]] High Speed 11898-2 CAN Transceiver (1st generation - Not recommended for new designs) 

----

===== MORNSUN =====
[[http://www.mornsun-power.com/ | MORNSUN]]
  * TD301MCAN and TD501MCAN, transceiver modules with integrated power isolation, signal isolation, CAN transceiver and bus protection in one module. 2500-VDC electric isolation, DIP8 package, operating temperature is -40 °C to +105 °C;  TD501MCAN with data transmission rate to 5 Mbit/s

===== NVE Non Volatile Electronics =====
[[www.nve.com/ | NVE]]
  * [[http://www.nve.com/Downloads/il41050.pdf | IL41050TT]]  IsoLoop® isolated CAN transceiver. ISO11898-2, operating at 5.0 and 3.3V, -55 to +125 °Celsius, transmit data dominant time-out, bus pin transient protection, thermal shutdown protection, short-circuit protection, 2,500 volt isolation

===== NXP =====
:-)

[[http://www.nxp.com/products/interface-and-connectivity/wired-connectivity/can-lin-flexray-transceivers/can-transceivers:MC_53485 | Overview]]


==== Secure CAN Transceivers ====
CAN/CAN FD transceiver family TJA115x provides a seamless and very efficient solution to secure classical CAN and CAN FD communication without using cryptography.
  * [[ https://www.nxp.com/docs/en/fact-sheet/SECURCANTRLFUS.pdf | TJA115x]] fact sheet (PDF)

==== Transceiver with active signal improvement SIC ====
CAN SIC transsceivers actively improve CAN signals to ensure robust communication in large networks and at faster bit rates.
[[https://www.nxp.com/docs/en/white-paper/CANSIGIMP-WP.pdf | CAN Signal Improvement]] (NXP PDF).

[[ https://www.nxp.com/products/interfaces/can-transceivers/can-signal-improvement:CAN-FD#/| TJA146x]] series actively improve CAN signals to ensure robust communication in large networks and at faster bit rates. Pin-compatible replacements to conventional HS-CAN transceivers, and backward compatible, fulfilling the ISO 11898-2:2016 specification. The TJA146x series fully embody the CiA601-4 2.0.0 specification.

  * [[https://www.nxp.com/products/interfaces/can-transceivers/can-signal-improvement/can-signal-improvement-capability-transceiver-with-standby-mode:TJA1462| TJA1462]] CAN transceiver with standby mode which is part of the TJA146x transceiver family that implements CAN signal improvement capability (SIC) as defined in CiA 601-4.
  * [[https://www.nxp.com/products/interfaces/can-transceivers/can-signal-improvement/can-signal-improvement-capability-transceiver-with-sleep-mode:TJA1463 | TJA1463]] CAN transceiver with sleep mode which is part of the TJA146x transceiver family that implements CAN signal improvement capability (SIC) as defined in CiA 601-4.
==== TJA1041 ====
High-speed CAN transceiver with standby and sleep mode
  * [[http://cache.nxp.com/documents/data_sheet/TJA1041.pdf | Data Sheet]]
  * [[http://cache.nxp.com/documents/application_note/AN00094.pdf | TJA1041/1041A]] high speed CAN transceiver, Application Note AN00094

==== TJA1052i ====
[[http://www.nxp.com/products/automotive/transceivers/can_transceivers/TJA1052IT.html | TJA1052i]] High-speed CAN transceiver that provides a galvanically isolated interface between a CAN protocol controller and the physical two-wire CAN bus. 


==== Mantis TJA1044/TJA1057 ====

[[http://www.nxp.com/products/automotive/transceivers/can_transceivers/series/NXP_MANTIS_HS_CAN_TRANSCEIVERS.html | Mantis]] family of ISO 11898-2 CAN transceivers with ‘chokeless’ EMC performance and support for **CAN FD** :-). The high-end "GT" variant guaranties critical parameters for CAN FD (Flexible Data rate) networks.
  * up to 2 Mbit/s for CAN FD
  * standby current of 10 µA
  * loop delay symmetry (required for CAN FD)

Jan 2014, Mantis CAN Transceivers are approved by Volkswagen for Chokeless use in vehicles.

  * [[http://www.nxp.com/products/interface_and_connectivity/can_lin_flexray_transceivers/TJA1044GT.html | TJA1044GT]] is ISO 11898-2 and ISO 11898-5 compliant.
    * loop delay symmetry (required for CAN FD) guaranteed for data rates up to 5 Mbit/s
    * Improved TXD to RXD propagation delay of 210 ns
  * [[http://www.nxp.com/products/interface_and_connectivity/can_lin_flexray_transceivers/TJA1057GT.html | TJA1057GT]] is ISO 11898-2 compliant.
    * loop delay symmetry (required for CAN FD) guaranteed for data rates up to 5 Mbit/s
    * Improved TXD to RXD propagation delay of 210 ns

==== TJA1052i ====
[[http://www.nxp.com/products/automotive/transceivers/can_transceivers/TJA1052IT.html | TJA1052i]] High-speed CAN transceiver that provides a galvanically isolated interface between a CAN protocol controller and the physical two-wire CAN bus. 

==== TJA1051 ====
[[https://www.nxp.com/part/TJA1051T#/ | TJA1051T]] High-speed CAN transceiver. Fully ISO 11898-2:2003 compliant. Timing guaranteed for data rates up to 5 Mbit/s in the CAN FD fast phase\\ Adafruit offers a small board, [[https://www.adafruit.com/product/5708 | CAN Pal]],  with the Transceiver and a 5V charge-pump voltage generator. No separate 5V power is required!
==== Dual CAN Transceiver ====

14-pin Dual-channel transceiver with low-power standby mode. Offers smaller board space in multi-channel CAN applications for data-rates up to 5 Mbit/s. Interfacing options for 3.3 V or 5 V supplied microcontrollers are available.

  * [[ https://www.nxp.com/products/analog/interfaces/in-vehicle-network/can-transceiver-and-controllers/dual-high-speed-can-transceiver-with-standby-mode:TJA1046TK | TJA1046TK]] Dual high-speed CAN transceiver with Standby mode
  * [[ https://www.nxp.com/products/analog/interfaces/in-vehicle-network/can-transceiver-and-controllers/dual high-speed-can-transceiver-with-standby-mode:TJA1059TK | TJA1059TK]] Dual high-speed CAN transceiver with Standby mode
  * [[ http://www.nxp.com/products/interface_and_connectivity/transceivers/can_transceivers/series/TJA1048.html|TJA1048T]] dual CAN transceivers based on the TJA1042, ISO11898-2 and ISO11898-5 compliant, for use in 12V and 24V systems. Transmit data dominant time-out function. SO14 and HVSON14 \\  [[http://www.nxp.com/documents/data_sheet/TJA1048.pdf| Data sheet]].

==== ISO11898-6 ====
    * TJA1145   ISO11898-6 transceiver, AUTOSAR R3.2.1 compliant 

==== System basis chip ====
  * UJA116x family with interesting compact HVSON14 package (3.5 x 5.5 mm):
    * UJA1161 Self-supplied high-speed CAN transceiver with Standby mode
    * UJA1162 Self-supplied high-speed CAN transceiver with Sleep mode
    * UJA1163 High-speed CAN system basis chip with Standby mode
    * UJA1164 High-speed CAN system basis chip with Standby mode & watchdog
    * UJA1167 High-speed CAN system basis chip with Standby/Sleep modes, watchdog & sensor supply
    * UJA1168 ([[http://www.nxp.com/documents/leaflet/75017167.pdf|PDF]]) High-speed CAN system basis chip for partial networking ISO11898-6 and CAN FD passive

==== CAN FD Shield transceiver ====
To overcome the interoperability problem with classic CAN and CAN FD, NXP presented a CAN Transceiver able to filter out CAN FD frames if used in a classic CAN only device. First information are available at [[http://www.can-newsletter.org/engineering/engineering-miscellaneous/140711_filters-can-fd-messages_nxp_BE/ | CiA]].


----

===== ON Semiconductors =====
:-)

[[http://www.onsemi.com/PowerSolutions/parametrics.do?id=178 | Overview]] 

  * [[http://www.onsemi.com/PowerSolutions/product.do?id=AMIS-30660 | AMIS-30660]] ISO 11898-2 (up to 1 Mb), Transmit Data Dominant Timeout 
  * [[http://www.onsemi.com/PowerSolutions/product.do?id=AMIS-41683 | AMIS-41683]] CAN low speed (ISO11898-3) transceiver
  * NCV7340
  * [[ http://www.onsemi.com/PowerSolutions/product.do?id=NCV7341 | NCV7341]] ISO 11898-2 (up to 1 Mb), Transmit Data Dominant Timeout Function, Bus Error Detection with Version NCV7341D20. 




----
===== Texas Instruments  =====
:-)

[[http://www.ti.com/lsds/ti/interface/can-technical-documents.page | Technical documents for CAN Transceivers]] 
  * Overview of 3.3V CAN (Controller Area Network) Transceivers
  * Q1 2009 Issue Analog Applications Journal
  * CAN EVM User's Guide
  * CAN Reference Guide
  * [[http://www.ti.com/lit/pdf/slly020 | Simplify CAN bus implementations with chokeless transceivers]]

TI offers a very sophisticated parametric selection tool
[[http://www.ti.com/lsds/ti/interface/can-products.page| parametric selection tool]] for CAN transceivers.
Try also the [[http://www.ti.com/lsds/ti/interface/can-products.page?rst=beta | new one ]] in beta stage.

[[http://www.ti.com/product/ISO1042 | ISO1042]] and [[http://www.ti.com/product/ISO1042-Q1 | ISO1042-Q1]] [[http://www.ti.com/lit/ds/symlink/iso1042-q1.pdf | PDF]] Isolated CAN Transceiver with 70-V Bus Fault protection and Flexible Data Rate :-)  Thwe Q1 is an automitive product

[[http://www.ti.com/lsds/ti/interface/can-products.page | TCAN33x]] family is compatible with the ISO 11898 CAN physical layer standard. The TCAN330, TCAN332, TCAN334, and TCAN337 are specified for data rates up to 1 Mbit/s. For the TCAN330G, TCAN332G, TCAN334G, and TCAN337G devices, data rates up to 5 Mbit/s  (“G” suffix) are available.

[[http://www.ti.com/tcan1042-pr-eu | TCAN1042x]] for use in CAN FD networks up to 2 Mbit/s. With the “G” suffix up to 5 Mbit/s. Low power standby mode with remote wake request feature.

[[http://www.ti.com/tcan1051-pr-eu | TCAN1051]] for use in CAN FD networks up to 2 Mbit/s. With the “G” suffix up to 5 Mbit/s. 

http://www.electronics-eetimes.com/news/can-fd-transceivers-offer-high-emc-performance-short-loop-delay/page/0/1
http://www.ti.com/tcan1042-pr-eu and http://www.ti.com/tcan1051-pr-eu.

CAN transceiver with fast loop times ( < 150 ns) for highly loaded CAN networks 
  * [[http://www.ti.com/lit/ds/symlink/sn65hvd255.pdf|SN65HVD255]]   ISO11898-2  SOIC-8
  * SN65HVD256   ISO11898-2  SIOC-8
  * SN65HVD257   ISO11898-2  SIOC-8 with additional RX Dominant Timeout and Fault Signal pin

[[http://www.ti.com/litv/pdf/sllsea2b|CAN Transceivers with Fast Loop Times for Highly Loaded Networks and Features For Functional Safety Networks]]

TI claims that CAN transceivers SN65HVD257, SN65HVD256 and SN65HVD255 are //CAN FD ready// up to 2 Mbit/s. They provide extremely short propagation delays.

  * [[http://www.ti.com/product/ISO1050 | ISO1050]] is a galvanically isolated CAN transceiver that meets the specifications of the ISO11898-2 standard. The device has the logic input and output buffers separated by a silicon oxide (SiO2) insulation barrier that provides galvanic isolation of up to 5000 VRMS for ISO1050DW and 2500 VRMS for ISO1050DUB
----
===== Vishay Siliconix =====

[[http://www.vishay.com|Vishay Siliconix]] Si9200EY CAN Bus Driver and Receiver.\\  [[http://www.vishay.com/docs/70015/si9200.pdf | Data Sheet]] \\ [[http://www.vishay.com/docs/70573/70573.pdf | AN602 application note]]

===== Yamar =====

  * [[http://yamar.com/product/dcan500/ | DCAN500]] transceiver enables a physical transmission of CAN messages on the DC power supply lines. Up to 500Kbit/s. Bits are QPSK modulated on the DC line and coupled to the DC line by means of capacitors.\\ [[https://can-newsletter.org/hardware/semiconductors/170413_can-over-powerline_dcan500_yamar/=cwt17-15&utm_medium=cwt-mail&utm_campaign=weekly-telegraph-17-15 | CAN Newsletter Online]]
Trace: • gigadevice • twin_can • xmos • dcd • profichip • can_cabling • oki • atmel • can_faq_basic_full • can_transceivers
Navigation

Search

Toolbox

QR Code
