Welcome to the CAN-bus Wiki project

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Next revisionBoth sides next revision
can_physical_layer:can_transceivers [2018/11/13 16:33] – [Analog Devices] ADM3055E heinzcan_physical_layer:can_transceivers [2020/12/11 10:37] – Transceiver with active signal improvement heinz
Line 17: Line 17:
  
 ===== Analog Devices ===== ===== Analog Devices =====
-  * [[https://www.analog.com/en/products/adm3055e.html |ADM3055E]] new member of the [[http://www.analog.com/en/content/CU_over_iCoupler_Digital_Isolation/fca.html|iCoupler]] family of galvanic-isolated CAN transceivers, complies with ISO 111898-2:2016, bit rates up to 12 Mbit/s, low loop delays of 150 ns, CAN-FD :-)+  * [[https://www.analog.com/en/products/adm3055e.html |ADM3055E]] new member of the [[http://www.analog.com/en/content/CU_over_iCoupler_Digital_Isolation/fca.html|iCoupler]] family of galvanic-isolated CAN transceivers, complies with ISO 111898-2:2016, bit rates up to 12 Mbit/s, low loop delays of 150 ns, ±40 V bus fault protection on CAN bus pins CAN-FD:-)
  
   * [[http://www.analog.com/en/interface/can/adm3054/products/product.html|ADM3054]] Transceiver with galvanic isolation, 3 channel [[http://www.analog.com/en/content/CU_over_iCoupler_Digital_Isolation/fca.html|iCoupler]]. Logic Voltage supply is 3.3V  or 5V, bus voltage supply 5V. Isolation 5KV<sub>RMS</sub>. Max bit rate 1Mbit/s , temp range -40°C to +125°C. 16pin SOIC-W.\\ [[http://www.analog.com/static/imported-files/data_sheets/ADM3054.pdf| Data Sheet(pdf)]]   * [[http://www.analog.com/en/interface/can/adm3054/products/product.html|ADM3054]] Transceiver with galvanic isolation, 3 channel [[http://www.analog.com/en/content/CU_over_iCoupler_Digital_Isolation/fca.html|iCoupler]]. Logic Voltage supply is 3.3V  or 5V, bus voltage supply 5V. Isolation 5KV<sub>RMS</sub>. Max bit rate 1Mbit/s , temp range -40°C to +125°C. 16pin SOIC-W.\\ [[http://www.analog.com/static/imported-files/data_sheets/ADM3054.pdf| Data Sheet(pdf)]]
Line 112: Line 112:
  
 ===== Microchip ===== ===== Microchip =====
 +  * [[https://www.microchip.com/wwwproducts/en/ATA6570 | ATA6570]] High-speed CAN FD Transceiver with Partial Networking, provides local and enhanced remote wake-up capabilities. Very low power consumption in Standby and Sleep Mode. Beside local wake-up via WAKE and remote wake-up pattern according to ISO 11898-2:2016 and also additionally supports ISO11898-2:2016 compliant CAN partial networking. Configuration the SPI. It also features a watchdog, a Serial Peripheral Interface (SPI) and automatic adjustment of the I/O levels to the I/O level of the connected microcontroller via the VIO pin. ATA6570 is a CAN-FD device but can be easily configured via the SPI as Non-FD for Classical CAN, CAN FD silent, CAN FD passive or as CAN FD active device, in order to fulfill the corresponding application requirements. :-)
   * [[ http://www.microchip.com/wwwproducts/en/MCP2542FD | MCP2542FD/4FD]] CAN FD Transceiver with Wake-Up on CAN activity,  Optimized for CAN FD at 2, 5 and 8 Mbps Operation, Maximum propagation delay 120 ns, Loop delay symmetry -10%/+10% (2 Mbps), ([[http://ww1.microchip.com/downloads/en/DeviceDoc/20005514A.pdf| PDF]]) :-)   * [[ http://www.microchip.com/wwwproducts/en/MCP2542FD | MCP2542FD/4FD]] CAN FD Transceiver with Wake-Up on CAN activity,  Optimized for CAN FD at 2, 5 and 8 Mbps Operation, Maximum propagation delay 120 ns, Loop delay symmetry -10%/+10% (2 Mbps), ([[http://ww1.microchip.com/downloads/en/DeviceDoc/20005514A.pdf| PDF]]) :-)
   * [[ http://www.microchip.com/wwwproducts/en/MCP2542FD | MCP2542WFD/4WFD]] CAN FD Transceiver with Wake-Up Pattern (WUP) Option, Optimized for CAN FD at 2, 5 and 8 Mbps Operation, Maximum propagation delay 120 ns, Loop delay symmetry -10%/+10% (2 Mbps), Wake-up on Pattern (WUP) as specified in ISO11898-2:2015, 3.6 μs activity filter time. [[http://ww1.microchip.com/downloads/en/DeviceDoc/20005514A.pdf| PDF]]) :-)   * [[ http://www.microchip.com/wwwproducts/en/MCP2542FD | MCP2542WFD/4WFD]] CAN FD Transceiver with Wake-Up Pattern (WUP) Option, Optimized for CAN FD at 2, 5 and 8 Mbps Operation, Maximum propagation delay 120 ns, Loop delay symmetry -10%/+10% (2 Mbps), Wake-up on Pattern (WUP) as specified in ISO11898-2:2015, 3.6 μs activity filter time. [[http://ww1.microchip.com/downloads/en/DeviceDoc/20005514A.pdf| PDF]]) :-)
Line 133: Line 134:
  
 [[http://www.nxp.com/products/interface-and-connectivity/wired-connectivity/can-lin-flexray-transceivers/can-transceivers:MC_53485 | Overview]] [[http://www.nxp.com/products/interface-and-connectivity/wired-connectivity/can-lin-flexray-transceivers/can-transceivers:MC_53485 | Overview]]
 +
 +
 +
 +
 +==== Secure CAN Transceivers ====
 +CAN/CAN FD transceiver family TJA115x provides a seamless and very efficient solution to secure classical CAN and CAN FD communication without using cryptography.
 +  * [[ https://www.nxp.com/docs/en/fact-sheet/SECURCANTRLFUS.pdf | TJA115x]] fact sheet (PDF)
 +
 +==== Transceiver with active signal improvement ====
 +
 +Read more on [[  https://www.nxp.com/docs/en/white-paper/CANSIGIMP-WP.pdf | CAN Signal Improvement]] (PDF). 
 +
 +
 +[[ https://www.nxp.com/products/interfaces/can-transceivers/can-signal-improvement:CAN-FD#/| TJA146x]] series actively improve CAN signals to ensure robust communication in large networks and at faster bit rates. Pin-compatible replacements to conventional HS-CAN transceivers, and backward compatible, fulfilling the ISO 11898-2:2016 specification. The TJA146 series fully embody the CiA601-4 2.0.0 specification.
 ==== TJA1041 ==== ==== TJA1041 ====
 High-speed CAN transceiver with standby and sleep mode High-speed CAN transceiver with standby and sleep mode
Line 163: Line 178:
  
 ==== Dual CAN Transceiver ==== ==== Dual CAN Transceiver ====
-    * [[http://www.nxp.com/products/interface_and_connectivity/transceivers/can_transceivers/series/TJA1048.html|TJA1048T]] dual CAN transceivers based on the TJA1042, ISO11898-2 and ISO11898-5 compliant, for use in 12V and 24V systems. Transmit data dominant time-out function. SO14 and HVSON14 \\  [[http://www.nxp.com/documents/data_sheet/TJA1048.pdf| Data sheet]].+ 
 +14-pin Dual-channel transceiver with low-power standby mode. Offers smaller board space in multi-channel CAN applications for data-rates up to 5 Mbit/s. Interfacing options for 3.3 V or 5 V supplied microcontrollers are available. 
 + 
 +  * [[ https://www.nxp.com/products/analog/interfaces/in-vehicle-network/can-transceiver-and-controllers/dual-high-speed-can-transceiver-with-standby-mode:TJA1046TK | TJA1046TK]] Dual high-speed CAN transceiver with Standby mode 
 +  * [[ https://www.nxp.com/products/analog/interfaces/in-vehicle-network/can-transceiver-and-controllers/dual high-speed-can-transceiver-with-standby-mode:TJA1059TK | TJA1059TK]] Dual high-speed CAN transceiver with Standby mode 
 +  * [[ http://www.nxp.com/products/interface_and_connectivity/transceivers/can_transceivers/series/TJA1048.html|TJA1048T]] dual CAN transceivers based on the TJA1042, ISO11898-2 and ISO11898-5 compliant, for use in 12V and 24V systems. Transmit data dominant time-out function. SO14 and HVSON14 \\  [[http://www.nxp.com/documents/data_sheet/TJA1048.pdf| Data sheet]].
  
 ==== ISO11898-6 ==== ==== ISO11898-6 ====

QR Code
QR Code can_physical_layer:can_transceivers (generated for current page)