Welcome to the CAN-bus Wiki project

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Next revisionBoth sides next revision
start [2016/12/23 14:56] heinzstart [2016/12/23 14:59] heinz
Line 5: Line 5:
 CAN was developed by [[http://www.bosch.com|BOSCH]]. The BOSCH CAN 2.0 B Specification can be downloaded at [[http://www.bosch-semiconductors.de/media/ubk_semiconductors/pdf_1/canliteratur/can2spec.pdf | Bosch]] or [[http://www.can-cia.org/standardization/specifications/|CiA]]. But now the CAN protocol is standardized by the ISO. The [[http://www.iso.org/iso/home/search.htm?qt=+11898&published=on |ISO 11898]] document is the reference for all CAN implementations. CAN was developed by [[http://www.bosch.com|BOSCH]]. The BOSCH CAN 2.0 B Specification can be downloaded at [[http://www.bosch-semiconductors.de/media/ubk_semiconductors/pdf_1/canliteratur/can2spec.pdf | Bosch]] or [[http://www.can-cia.org/standardization/specifications/|CiA]]. But now the CAN protocol is standardized by the ISO. The [[http://www.iso.org/iso/home/search.htm?qt=+11898&published=on |ISO 11898]] document is the reference for all CAN implementations.
  
-  * [[http://www.iso.org/iso/home/store/catalogue_tc/catalogue_detail.htm?csnumber=33422|Part 1]] specifies the data link layer (DLL) and physical signalling of the controller area network (CAN) protocol. The latest is ISO11898-1:2015 including CAN FD (ISO11898-2:2016)  +  * [[http://www.iso.org/iso/home/store/catalogue_tc/catalogue_detail.htm?csnumber=33422|Part 1]] specifies the data link layer (DLL) and physical signalling of the controller area network (CAN) protocol. The latest is ISO11898-1:2015 including CAN FD 
-  * [[http://www.iso.org/iso/home/store/catalogue_ics/catalogue_detail_ics.htm?csnumber=67244 |Part 2]] specifies the high-speed (non fault-tolerant) physical layer (transmission rates of up to 1 Mbit/s and more for CAN FD)+  * [[http://www.iso.org/iso/home/store/catalogue_ics/catalogue_detail_ics.htm?csnumber=67244 |Part 2]] specifies the high-speed (non fault-tolerant) physical layer (transmission rates of up to 1 Mbit/s and more for CAN FD, ISO11898-2:2016
   * [[http://www.iso.org/iso/home/store/catalogue_tc/catalogue_detail.htm?csnumber=36055|Part 3]] describes the low-speed fault-tolerant physical layer at transmission rates above 40 kBit/s up to 125 kBit/s.   * [[http://www.iso.org/iso/home/store/catalogue_tc/catalogue_detail.htm?csnumber=36055|Part 3]] describes the low-speed fault-tolerant physical layer at transmission rates above 40 kBit/s up to 125 kBit/s.
   * [[http://www.iso.org/iso/home/store/catalogue_tc/catalogue_detail.htm?csnumber=36306|Part 4]] specifies the time-triggered communication (TTCAN) protocol which supports distributed real-time control and multiplexing for use within road vehicles   * [[http://www.iso.org/iso/home/store/catalogue_tc/catalogue_detail.htm?csnumber=36306|Part 4]] specifies the time-triggered communication (TTCAN) protocol which supports distributed real-time control and multiplexing for use within road vehicles

QR Code
QR Code start (generated for current page)